- Home
- ยป
- Our Product Range
- »
- Bostik Products
Bostik Products
Bostik offers a full range of waterproofing and crack isolation products. Waterproofing is an important element in protecting your investment. It prevents water from leaking into unwanted areas where it can cause damage. At times, this damage will be unseen until it is too late. Ensure that your next project includes properly installed Bostik waterproofing systems. Typical types of areas that require waterproofing are: laundries, shower stalls, bathrooms, kitchens, swimming pools and spas.Product lines featured in our waterproofing range include:
- Bond breakers / bandages
- Waterbased membranes
- Polyurethane membranes
Bostik LVEP Epoxy Grout
Minimum Order Quantity: 8 Kg
Product Brochure
Brand | Bostik |
Usage/Application | For injecting into narrow gaps, cracks and voids ranging from 0.25 mm to as wide as 9 mm |
Type | Free non pigmented two component system based on liquid epoxy resin with a special hardener |
Form | Liquid |
Shelf Life | 12 months |
Country of Origin | Made in India |
Bostik LVEP is a solvent free non pigmented two component system based on liquid epoxy resin with a special hardener designed for injecting into narrow gaps, cracks and voids ranging from 0.25 mm to as wide as 9 mm.
- Low viscosity, high capillary action – deep penetration, can be injected into fine cavities and narrow gaps.
- Very hard and abrasion resistant.
- Very high mechanical strength properties – withstands heavy loads and stress.
- Non shrink – fills up voids and cracks completely.
- Weather and water proof.
- Resistant to waste and sea water.
- Suitable for dilute inorganic acids, lyes and mineral oil.
Bostik Low Viscous Epoxy Injection Resin Grout
Product Brochure
Usage/Application | chemical |
Packaging Size | 1 to 4 Kg |
Type | Liquid |
Yield | 1.05 to 1.10 g/mL |
Brand | Bostik |
Country of Origin | Made in India |
- Building Chemicals
- Low viscosity & rapid strength gaining
- High mechanical strength
- Good chemical resistant
Description:
- Epoxy Injection Grout consists of solvent free epoxy resin with low viscous liquid
- hardener. Epoxy injection grout may be placed by free flow under gravity or may be injected using suitable hand or mechanical pump. Grouting of a gap dimensions
- 0.1mm to10mm may be easily achieved
Uses:
- Crack injection application
- Filling and bonding of cracked concrete
- Structural support where thin section grouting is required
- Structural support where dynamic load resistance is required
- Bonding of lifted floor toppings
Application Procedure:
- Surface Preparation:Ensure that grouting surfaces are free from dust and oil contamination Small gaps may be blown out by using clean dry compressed air Steel should be free of rust and flaking mill scale All work surfaces must be dry
Mixing:
- Add entire content hardener into base
- Mix thoroughly for 2 minutes with slow speed stirrer until to get homogeneous
Placing:
- Pouring Under Gravity: For supporting structures, where epoxy injection grout is being poured under gravity, the use of a grout tight shutter is essential .This may be constructed from timber and sealed using fast set mortar. Apply a mould releasing agent to the form work surfaces which will affect release after the grout has hardened.
Crack Injection:
- Drill and fix suitable injection tubes at approximately 300mm centers along the crack line using fast set mortar for fixing the tubes and facing up the crack. Use low pressure pump to inject mixed grout starting at the lowest point of the crack and work upwards to the highest point sealing off each injection point in turn
- Allow grout to cure for at least 24 hours .Cut off external parts of injection tubes and tools and equipment should be cleaned with solvent prior to grout setting
Storage and Shelf Life:
- Bostik LVEP as supplied shall be stored in a cool and dry place away from sunlight, moisture and high humidity and have a shelf life of 12 months in the original packing.
Health and Safety:
- Bostik LVEP contains organic resins and hardeners which may cause sensitization by skin contact. Avoid contact with skin and eyes and inhalation of vapour. In case of contact, wash liberally with water and seek medical advice, if required. Wear suitable protective clothing, gloves and goggles while handling.
Fire:
- Bostik LV EP is inflammable. No naked flame should be allowed near the site.
- Do not smoke during use.
Bostik Flow Fill Grout
Minimum Order Quantity: 30 Kilogram
Product Brochure
Brand | Bostik, Fosroc, Sika, Basf, Balendura, Caldrys |
Form | Powder |
Packaging size | 30, 25 Kg |
Usage | Rapid Strength Gain Vibration Resistant Corrosion Resistant Non Expansive Can Be Placed Under Water |
Grade | Construction |
Grade Standard | Non Shrink Cement |
Shelf Life | 12 months |
Packaging Type | 30, 25 Kg |
Bar Diameter (mm) | 12 to 40 mm |
Material | Non Shrink Cement |
Model Number | S |
Application | Grouting Of Base Plates Of Turbines, Compressors, Boiler Feed Pumps etc. |
Flowfill grout GP is a multipurpose non-shrink cementitious grout. Flowfill Grout GP is based on Portland cement, graded aggregate and chemical additives, which impart controlled expansion whilst in the plastic state. The gaseous expansion system compensates for shrinkage and settlement in the plastic state.Used in All general purpose grouting,Precast and prestressed panels,Grouting in column based, base infilling,Filling core holes, rod holes and defects in concrete,Fill in grout for hollow block walls,Joints between precast panels and other joints,Till slab panels,Caulking of joints and pipes.
Flowfill Grout Gp
Minimum Order Quantity: 1 Bag
Product Brochure
Usage/Application | Non Shrink Cementitious Grout |
Grade | Construction |
Packaging Size | 30 kg |
Packaging Type | Bag |
Features | Non Shrink Grout |
Type | Bag |
Color | Grey |
Thickness | Maximum Thickness 50 mm |
Compressive Strength N Per Mm | 28 days - 60n per mm2 |
Form | Powder |
Shelf Life | 12 Months |
Flowfill Grout GP MY is a multi-purpose non-shrink Class-A cementitious grout. It is based on portland cement, graded aggregate and chemical additives , which impart controlled expansion whilst in the the plastic state. The gaseous expansion system compensates for shrinkage and settlement in the plastic state.
Recommended uses
All general purpose grouting
Precast and prestressed panels
Grouting in column based, base infilling
Fill core holes, rod holes and defects in concrete
Fill in grout for hollow block walls
Joints between precast panels and other joints
Till slab panels
Caulking of joints and pipe
Bostik Superfixall Tile Adhesive
Minimum Order Quantity: 30 Bag
Product Brochure
Types | Ceramic, Stone, Vitrified |
Application | Tile On Tile |
Categories | Cementitious |
Pack Type | Bag |
Surface of Application | Ceramic |
Usage | Fixing Tile, Pavers, Granite and Marble |
Form | Powder |
Packaging Size | 30 kgs |
Thickness (millimetre) | 3 mm |
Color | White |
Grade Standard | Superfixall |
Material | Adhesive |
Shelf Life | 12 months |
Appearance | Powder |
Bed Thickness | 3mm |
Silver Star | Available |
Coverage | 2.5 kg/m2 |
Superfixall is an exceptionally high strength, fast setting, high quality waterproof adhesive developed to bond all types of ceramic tiles, fully vitrified tiles, as well as natural stone, marble, granite and mosiac tiles onto brickwork, cement render and concrete walls and floors. Suitable for both internal, external & tile on tile application.
Benefits:
- high strength bond.
- no odour.
- economical.
- water cleanable.
- non toxic.
- easy to spread.
- interior / exterior use for wall and floor.
- thick & thin bed application.
Recommended for:
- concrete.
- cement render.
- brickwork.
- blockwork.
- swimming pools.
- tile on tile.
Installation:
surface preparation : all surface must be clean, dry, free from dust, grease, wax, oil, curing compounds and all other contaminants likely to prevent the adhesive bonding.
concrete should be allowed to cure for at least 28 days and cement render 7 days prior to tiling. A wood float finish is preferred.
Expansion joints:
movement joints should be incorporated in the tile layout.
Mixing:
30 kg. Of superfixall powder requires approx. 7. 2 to 7. 8 litres of water which produces 20. 4 litres of mixed product. Mix superfixall and water in the ratio 3:1 by volume. Add a measured amount of water into a clean container and sprinkle superfixall powder slowly into the liquid with constant stirring. Eliminate lumps. Mix to a thick paste consistency. Allow to stand for 2 minutes then remix. The adhesive is now ready to use.
Bostik Elastocoat Waterproofing
Minimum Order Quantity: 1 Piece
Product Brochure
Form of Chemical | Liquid |
Brand | Bostik |
Types | Masonry, Acrylic |
Surface of Application | Roofs, Concrete |
Color | White & Teracotta |
Packaging Type | Can |
Packaging Size | 20 ltr |
Shelf Life | 12 months |
Material | Electromeric |
Weight (Kg) | 27 |
Form | Liquid |
Grade Standard | Waterproofing |
Areas of application:
- rcc structure
- masonry walls
- sloping / flat roofs
- cooling tower
- bridges
- reliable crack bridging.
- low water absorption.
- high alkali resistance.
- low dirt pick up.
- seamless membrane with good breathability.
- long term exterior durability.
- uv resistant.
- water based & environment friendly.
- can be tinted to desired shades.
- surfaces should be free from oil, dust and other contaminants.
- any deficiencies on the surface should be rectified before applying bostik sealer coat.
- dilute bostik sealer coat up to 10% by volume with potable water.
- apply sealer coat for better adhesion & sealing.
- allow the sealer coat to dry for 2 hrs.
- dilute bostik elastocoat upto 20% by volume with potabl water.
- apply first bostik elastocoat by roller or brush on the primed surface.
- allow drying for 4-5 hours before application of second coat.
Bostik Bosco Cem 475
Minimum Order Quantity: 1 Piece
Product Brochure
Form of Chemicals | Liquid |
Brand | Bostik |
Usage/Application | Waterproofing Cum Bonding Agent |
Category | Acrylic Based Polymer Coating, Waterproofing Coating, Cementitious Waterproofing, Bitumen Membrane, Crystalline Waterproofing |
Application | Construction |
Shelf Life | 12 months |
Pot life | 30 min |
Packaging Type | Bucket |
AREAS OF APPLICATION:-
Bonding agent for old and new concrete.
Repair damaged, spawlled concrete and filling of cracks.
Suitable for water proofing and laying floor screeds.
FEATURES & BENEFITS:-
Good adhesion to concrete / masonry surfaces.
Improving tensile and flexural properties of repair mortar.
Reduces water penetration and shrinkage.
Better abrasion and chemical resistance of cement screed.
Clients can avail from us this range of Boscocem 475 Sbr Latex at most affordable prices.
Bostik Boscocem 475 Building Chemical
Minimum Order Quantity: 5 Litre
Product Brochure
Usage/Application | Waterproofing |
Category | Waterproofing Coating |
Type | Coating |
Brand | Fosroc, Bostik, Basf, Sika, Zicosil |
Packaging Size | 1, 5, 20, 50 ltr |
Color | White |
Shelf Life | 12 months |
Packaging Type | Bucket |
Form Of Chemical | Liquid |
Physical State | Liquid |
We are involved in providing fine quality range of Boscocem 475 Sbr Latex to our most valued clients. Our range of Boscocem 475 Sbr Latex is widely appreciated by our clients.
AREAS OF APPLICATION:-
Bonding agent for old and new concrete.
Repair damaged, spawlled concrete and filling of cracks.
Suitable for water proofing and laying floor screeds.
FEATURES & BENEFITS:-
Good adhesion to concrete / masonry surfaces.
Improving tensile and flexural properties of repair mortar.
Reduces water penetration and shrinkage.
Better abrasion and chemical resistance of cement screed.
Clients can avail from us this range of Boscocem 475 Sbr Latex at most affordable prices.
Polyester Resin Based Anchor Grout, Bostik, Cera, Fosroc
Product Brochure
Brand | Gosroc, Bostik, Cera, Myk Arment |
Usage/application | Rebaring Chemical |
Industry | Construction |
Packaging Size | 1 kg |
Type Of Construction | Civil |
Type | 2 Component |
Color | Black |
Shelf Life | 6 months |
Country of Origin | Made in India |
Bostik Anchor grout
fosroc lock fix
Myk arment
Cer chem anchorset
Bostik Elastocoat Waterproofing
Minimum Order Quantity: 1 Piece
Product Brochure
Brand | Fosroc, Bostik |
Color | White |
Packaging Size | 1,5, 20, 50,100 ltr |
Packaging Type | Can |
Types | Masonry |
Usage | Industrial |
Usage/Application | Roofs |
Shelf Life | 12 months |
Material | Waterproofing |
Form | Liquid |
Bostik Epoxy Coat Uw
Product Brochure
Brand | Bostik |
Packaging Size | 5 Kg |
Usage/Application | Swimming Pool, Water Tank |
Grade Standard | Food Grade |
Color | White, Blue |
No. Of Components | Two Component |
Bostik Seal N Flex 1
Minimum Order Quantity: 1 Piece
Product Brochure
Brand | Bostik |
Usage/Application | Glass, Wood |
Usage | Gap Sealant |
Packaging Size | 600 gms |
Shelf Life | 12 months |
Features | Water Resistant |
Can Be Painted | Yes |
Weather Resistant | Yes |
Grade Standard | Chemical Grade |
Condition | New |
Bostik Seal 'N' Flex 1 is a one component, low modulus, polyurethane elastomeric joint sealant curing via atmospheric moisture to form an elastic and strong weatherproof seal for use in expansion, isolation and construction joints in concrete and masonry structures.
Seal 'n' flex 1 is a low modulus, one component, class a polyurethane sealant. When cured it will form a tough, flexible seal capable of cyclic expansion and compression movement of 50% (+25%) of the original joint width. Seal 'n' flex 1 is virtually unaffected by normal weathering conditions such as rain, sunlight, snow, sleet, ultra- violet radiation, ozone, atmospheric contamination and pollution. Its excellent weatherability enables it to retain its original properties after years of exposure, refer to the csiro rilem long-term sealant durability study dbce doc. 97/196 (m).
Recommended uses:
sealing expansion / construction joints in :
- insitu concrete.
- precast and tilt up panels.
- brick & blockwork.
- plasterboard.
- aluminium windows.
- granite, sandstone and marble.
- grc, fibreglass & speciality panel systems.
- metal curtain wall.
- water tanks.
- sealing contraction / longitudinal / expansion joints in concrete roads.
Features & benefits:
- low modulus 50% (+25%).
- excellent durability.
- acoustic rated.
- one component, no mixing required.
- australian made.
- colour range.
- paintable (refer limitations).
- non staining.
Approvals / standards:
- csiro rilem long - term sealant durability study dbce doc. 97/196(m).
- iso 11600 - class f-25 lm.
- din 18540 (german), snjf (french) & bs 4254-
1983 approval as a low modulus external joint sealant.
- astm c. 920-87 & 98 (usa) as type s, bs 5212
part ii 1990, grade ns, class 25, g,a,m & o as an external joint sealant.
- as4020 1992 potable water approval.
- as1157 - 1972 resistance to fungal growth ministry and agriculture and fisheries new zealand(meat, fish, game, poultry).
Bostik Cwp 30 kg
Minimum Order Quantity: 1 Bag
Product Brochure
Usage/Application | Waterproofing |
Category | Crystalline Waterproofing |
Types | Waterproofing Coating, Crystalline Waterproofing, Cementitious Waterproofing |
Brand | Bostik |
Packaging Size | 30 kg |
Packaging Type | Bag |
Type | Water Proofing Compounds |
Material | Crystalline |
Color | Grey |
Storage Condition | Regular |
Solubility | Powder |
Shelf Life | 12 months |
Application | Construction |
Condition | New |
Bostik cwp is a surface applied, integral crystalline waterproofing material, which waterproofs and protects concrete in depth. It consists of portland cement, specially treated quartz sand and a compound of active chemicals. Bostik cwp needs water only to be mixed prior to the
application. When bostik cwp is applied to a concrete surface the active chemicals combine with the free lime and moisture present in the capillary tracts of the concrete to form an insoluble, crystalline structure. These crystals fill the pores and minor shrinkage cracks in the concrete to prevent any further ingress, still allowing the concrete to breathe.
Product Uses:
bostik cwp can be applied to all structurally sound concrete - new or old. It may be applied to either the positive or negative sides of the concrete face.
Typical areas of application are :
- water tanks / towers
- reservoirs / dams
- swimming pools
- water treatment works
- canals & harbours
- basements / foundations
- tunnels
- retaining walls
- bridge decks etc.
Features and benefits:
- becomes an integral part of the concrete, forming a complete body of strength and durability.
- penetrates deeply and seals concrete's capillary tracts and shrinkage cracks.
- can be applied from either positive or negative side.
- completely effective against high hydrostatic pressure.
- easy to apply, less labour and cost effective.
- becomes an integral part of the substrate - cannot be removed easily.
- back filling can be done without further protection like placement or steel or wire mesh.
- can be used in the ph range of 3-11.
- can be applied to moist or green concrete.
- non toxic. Can be used for potable water applications.
- water treatment works.
- canals & harbours.
- basements / foundations.
Application procedure:
surface preparation: all concrete to be treated with bostik cwp must be clean and have an "open" capillary
Additional Information:
- Pay Mode Terms: T/T (Bank Transfer),cash
Bostik Boscolastic Waterproofing Chemicals
Minimum Order Quantity: 1 Kit
Product Brochure
Category | Waterproofing Coating, Acrylic Based Polymer Coating, Cementitious Waterproofing |
Color | Gray |
Packaging Size | 17.5 kgs, 35 Kgs |
Usage/Application | Concrete |
Types | Acrylic, Masonry |
Surface of Application | Roofs, Concrete |
Application | Construction |
Self Life | 12 months |
Form | Powder, Liquid |
Usage | Waterproof Coating |
Brand | Bostik |
Product Description:Boscolastic is a two component flexible acrylic polymer
cementitious waterproofing coating that is mixed on site and resurfaced on concrete and other construction materials to waterproof. Boscolastic has excellent weathering resistance and crack bridging property.
RECOMMENDED USES:
- Water Tanks.
- Bathrooms, Blaconies, Terraces.
- Swimming pools and pool decks.
- Water Features and ponds
- Planter Boxes, Canopies.
- On external environmental deck.
- In between or under floor toppings.
FEATURES & BENEFITS:
- Flexible, elastic & can bridge cracks.
- Accommodates flexible movements in suspended structures.
- Can be tiled over successfully.
- Bonds well to sound substrates.
- Ability to withstand heavy topping without fracture.
- Applied on damp walls and floors
- Can be painted over with elastic paints.
- Hard and abrasion resistant.
DAMPEN:
All concrete and cement substrates shall be saturated with clean water before applying Boscolastic waterproof coating.
No free standing water is present during application.
SURFACE PREPARATION:
All substrates shall be sound and free from dust, excess mortar, oil other loose particles.
Cracks or honeycombs shall be repaired using suitable cement mortar.
MIXING:
Empty liquid component in a clean container and slowly add the Powder component whilst stirring using a slow speed (500-600 rpm) electric drill with a suitable paddle. Minimal amount of water may be added to ease application only when necessary. Small amount may be hand-mixed separately. Mix until homogeneous slurry is obtained and make sure that no unmixed power is left at the bottom of the container.
Tile joint filler
Minimum Order Quantity: 50 Kilogram
Product Brochure
Material | Joint Filler |
Packaging size | 1 kg |
Packaging Type | Pouch |
Grouting Gap Range (mm) | 2,3 mm |
Shelf Life | 12 months |
Color | As Per Shadecard |
Application | Tile Joint Grout |
Brand | Bostik India Pvt Ltd, Fosroc, Laticrete, Bal endura |
Epoxy Tile Joint Filler
DescriptionBostik Epoxy Tile Grout is a three component system based on speciality formulated epoxy resins and hardeners , especially for use in applications of ceramic tile, vitrified tile and sand stone .
Recommended uses:
It is an ideal material recommended for
Shopping Malls & Show rooms, Hotels, Kitchens & Bath rooms, Swimming Pools, Residential and commercial building etc.
Cementious tile joint filler
Descriptionsuitable for the joint filling in wall and floor
Benefits:
Easy to apply and clean , Good adhesion, Resistance to shrinkage and cracking.
Additional Information:
- Pay Mode Terms: T/T (Bank Transfer),cash
- Packaging Details: 1 kg
Bostik Bosco Cem 475
Minimum Order Quantity: 1 Litre
Product Brochure
Usage/Application | Bonding Agent For Old And New Concrete & Repair Damaged, Spawlled Concrete And Filling Of Cracks |
Type | Coating |
Packaging Size | 5, 50, 100, 200 kgs |
Packaging Type | Bucket |
Shelf Life | 12 months |
Water Absorption | Reduces Water Absorption Of Mortar |
Consumption | Depends Upon Application Area |
Total Solids | 48% |
Color | White Crystal |
Grade Standard | Construction |
Physical State | Liquid |
Usage | Personal |
Application | Construction |
Brand | Bostik |
Category | Acrylic Based Polymer Coating |
Form of Chemicals | Liquid |
pH Value | 7 - 9 |
Purity | 45% solid content |
Specific Gravity | 1.03 |
Storage Condition | Cold Place |
Viscosity | Low |
Product description:
BOSTIK BOSCOCEM 475 SBR is a Styrene Butadiene Based Mortar Modifying Bonding Agent.
AREAS OF APPLICATION Bonding agent for old and new concrete. Repair damaged, spawlled concrete andfilling of cracks. Suitable for water proofing and laying floor screeds.
Pack: 20 Litre
FEATURES BENEFITS Good adhesion to concrete / masonry surfaces. Improving tensile and flexural properties of repairmortar. Reduces water penetration and shrinkage. Better abrasion and chemical resistance ofcement screed.
Bostik Floor Hardener
Minimum Order Quantity: 1 Bag
Product Brochure
Packaging Size | 30 kgs |
Brand | Bostik |
Material | Non Metallic Floor Hardener |
Usage/Application | Floor Hardener |
Color | Grey |
Physical State | Powder, Crystal |
Form | Dry |
Packaging Type | Bag |
Weight | 30 kgs |
Shelf Life | 12 months |
Dry Solids Content | Yes |
Bostik Floor Hardener NM is a pre-blended, ready to use and dry shake formulation for hardening freshly placed horizontal concrete slabs and toppings. Floor Hardener NM produces a hard, dense, wear resistant surface which resists corrosion and absorption of grease, oils, alkalis and most chemicals. Typical areas of use include concrete floors in garages, steel mills, generating plants, loading platforms and wherever is heavy-duty wear resistant floor finish is required.
Bostik Elastocoat
Minimum Order Quantity: 1 Can
Product Brochure
Category | Acrylic Based Polymer Coating |
Grade | Waterproofing |
Physical State/Form | Liquid |
Type | Water Proofing Compounds |
Grade Standard | Reagent Grade |
Brand | Bostik |
Elastocoat is a high performance Elastomeric acrylic based water proofing coating with antifungal and crack bridging ability. Recommended for protection of exterior cementitious surfaces.
Bostik Moisture Seal
Minimum Order Quantity: 1 Litre
Product Brochure
Category | Acrylic Based Polymer Coating, Cementitious Waterproofing, Waterproofing Coating, Primer Coating |
Physical State | Liquid |
Types | Acrylic Based Polymer Coating, Damp Guard Coating |
Form of Chemicals | Liquid |
Brand | Bostik |
Packaging Size | 1 ltr, 5 ltr |
Grade Standard | Construction |
Shelf Life | 12 months |
Application | Construction |
Condition | New |
Recommended Uses:
* As low vapour transmission barrier membrane prior to the application of Bostik ultraset Timbre flooring adhesive.
* As a low vapour transmission barrier membrane coating in the building and construction industries and as a barrier coating over "green",fleshly laid concrete.As a waterproofing membarane to prevent water seepage or moisture penetration through to the interior of walls and floors.
* As a waterproof membrane.curing compound and barrier coating over fleshly laid hardened green concrete either as internal finish or prior to the application of conventional floor and wall coverings such as tile adhessives,carpets or conventional building parts.
* As a waterproof vapour barrier in tanking applications and sealing over damp concrete surface either as internal finish coatings or prior to over coating with other coatings.
* A highly tolerant membrane /barrier to prevent water seepage or permeation for floor walls,water storage tanks or reservoirs and swimming pools.
* Safe to use sensitive locations ( eg. Around food or habitable areas.)
* May be used as waterproof primer prior to the application of Ultraseal,Boascoseal PU,one and two part polyurethene sealents and cementitious floor screeds.
Features and Benifits:
+ Environmentally friendly.
+ Easy clean-up using water.
+ Cured membrane will withstand high levels of hydrostatic pressure up to 25 metre head of water.
+ Potable water approval
+ Can be safely applied to fleshly laid hardened green concrete.
+ Non- flammable,negligibl odour and toxicity.
+ Has excellent adhesion to most substrate including brick,masonry,concrete,brick concrete,compressed fibreboard,stone,timber.
+ Convenient equal part mixing ratio ( bu volume)
Performance Properties:
Appearance - Brushable / rollable/(mixed) Sprayable uniform paste with a matt appearance.
Colour - light grey
Finish - Matt
Mixing ratio - 1 : 1 (component A :B) by volume or 1:1 by weight (A:B)
Pot life - 45 - 60 minutes @ 25 c
Recoat time - 2 hours
Application of Adhesive / coverings - 24 hrs
Full cure - 5 - 7 days @25 c and 50% RH
Dry film thickness - 200 microns
Coverage :
Applied by roller the first coat at 5m2/litre.Second coat at 5m2/litre.Coverage dependent on surface porosity and subtrate conditon. Moisture seal is disigned to be applied in two coats to achieve a approximate dry film thickness of 200 micrones.
Additional Information:
- Pay Mode Terms: T/T (Bank Transfer),cash
Bostik EP Bond
Minimum Order Quantity: 12 Kg
Product Brochure
Type | Epoxy Based |
Packaging Size | 1 kg |
Grade Standard | Construction |
Coverage | 30 sq ft approx |
Packaging Type | Bottle |
Features | Bonding Agent For Old and New Concrete |
Shelf Life | 12 months |
Surface of Application | Concrete |
DESCRIPTION Bostik Crack Fill is high performance Polymer modified cementitious Crack Sealer for sealing / repairing internal and external cracks in plasters and masonry surface.
FEATURES & BENEFITS Single component. Non - shrinking. Better adhesion. Smooth finish.
APPLICATION PROCEDURE Develop the crack in a “V” shaped groove. Clean the groove by sprinkle of water to remove all the loose particles and dust. Mix proportion Crack filler : Water - 3 :1 PBV. Mix Crack Filler in water in a clean container. Mix for 2 - 3 minutes to get smooth homogeneous paste. Apply this paste into the groove with suitable trowel. Finish the surface as required.
Bostik CWP Chemical
Product Brochure
Usage/Application | Crystalline Waterproofing |
Brand | Bostik |
Coverage | Water retaining structures, Internal concrete wall surfaces, Two coats of Bostik CWP at 0.65 - 0.8 |
Category | Cementitious Waterproofing, Crystalline Waterproofing, Waterproofing Coating, Acrylic Based Polymer Coating |
Color | Grey |
Waterproofing Type | Crysatlline |
Grade Standard | Construction |
Form of Chemicals | Powder |
Shelf Life | 12 months |
Packaging Type | Bag |
Application | Construction |
Application/Usage | Waterproofing |
application. When bostik cwp is applied to a concrete surface the active chemicals combine with the free lime and moisture present in the capillary tracts of the concrete to form an insoluble, crystalline structure. These crystals fill the pores and minor shrinkage cracks in the concrete to prevent any further ingress, still allowing the concrete to breathe.
Product Uses:
bostik cwp can be applied to all structurally sound concrete - new or old. It may be applied to either the positive or negative sides of the concrete face.
Typical areas of application are :
- water tanks / towers
- reservoirs / dams
- swimming pools
- water treatment works
- canals & harbours
- basements / foundations
- tunnels
- retaining walls
- bridge decks etc.
Features and benefits:
- becomes an integral part of the concrete, forming a complete body of strength and durability.
- penetrates deeply and seals concrete's capillary tracts and shrinkage cracks.
- can be applied from either positive or negative side.
- completely effective against high hydrostatic pressure.
- easy to apply, less labour and cost effective.
- becomes an integral part of the substrate - cannot be removed easily.
- back filling can be done without further protection like placement or steel or wire mesh.
- can be used in the ph range of 3-11.
- can be applied to moist or green concrete.
- non toxic. Can be used for potable water applications.
- water treatment works.
- canals & harbours.
- basements / foundations.
Application procedure:
surface preparation: all concrete to be treated with bostik cwp must be clean and have an "open" capillary
Bostik Moisture Seal
Product Brochure
Category | Waterproofing Coating |
Color | Transparent |
Types | Waterproofing Coating |
Form of Chemicals | Liquid |
Brand | Bostik |
Is It Waterproof | Waterproof |
Packaging Type | Bucket |
Shelf Life | 12 months |
Usage/Application | Construction |
Condition | New |
Recommended Uses:
as low vapour transmission barrier membrane prior to the application of bostik ultraset timber flooring adhesive.
as a low water vapour transmission barrier membrane coating in the building and construction industries and as a barrier coating over “green”, freshly laid concrete.
as a waterproofing membrane to prevent water seepage or moisture penetration through to the interior of walls and floors.
as a waterproof membrane, curing compound and barrier coating over freshly laid hardened (green) concrete either as a internal finish or prior to the application of conventional floor and wall coverings such as tile adhesives, carpets or conventional building paints.
as a waterproofing vapour barrier in tanking applications and sealing over damp concrete surface either as an internal finish coating or prior to over coating with other coatings.
a highly tolerant membrane / barrier to prevent water seepage or permeation for floors, walls, water storage tanks or reservoirs and swimming pools.
safe to use in sensitive locations (e. G. Around food or habitable areas).
may be used as a waterproof primer prior to the application of ultraseal, boscoseal pu, one and two
part polyurethane sealants or cementitious floor screeds.
Features and benefits:
• environment friendly.
• easy clean - up using water.
• cured membrane will withstand high levels of hydrostatic pressure upto 25 metre head of water or 250 kpa.
• can be applied to damp surfaces.
• potable water approval.
• can be safety applied to freshly laid hardened (green) concrete.
• non-flammable, negligible odour and toxicity.
• has excellent adhesion to most substrate including brick, masonry, concrete, block concrete, compressed fibreboard, stone and timber.
• convenient equal part mixture ratio (by volume).
Additional Information:
- Pay Mode Terms: T/T (Bank Transfer)
Bostik Floor Hardener
Minimum Order Quantity: 30 Bag
Product Brochure
Packing Size | 25 kg |
Brand | Fosroc, Bostik, Cico, Sika, Basf, Balendura |
Material | Non metallic floor hardener |
Usage/Application | Floor Hardner |
Color | Grey |
Packing Type | Bag |
Form | Powder |
Packaging Type | Bag |
Grade | Flooring |
Weight | 30 |
Quantity Per Pack | 30, 25 kgs |
Shelf Life | 12 months |
Grade Standard | Non Metallic Floor Hardner |
Coverage | 3.5kg/m2 |
Application | Flooring |
Country of Origin | Made in India |
Application / End use:
Used to provide a heavy duty concrete floor subject to heavy loads and traffic such as workshops,warehouses,car parks,garages,production area,hospitals,schools,shopping centre,loading bays,industrial complexes,etc
Coverage:
2- 3 kg/m2 for light traffic
3 -4 kg/m2 for medium trafffic
4 -5 kg/m2 for heavy traffic
Additional Information:
- Pay Mode Terms: T/T (Bank Transfer),cash
Bostik Epoxy Coat Uw
Minimum Order Quantity: 1 Kg
Brand | Bostik |
Color | Blue |
Category | Floor Coating, Wall Coating |
Types | Water-Based |
Packaging Size | 5 |
Shelf Life | 12 months |
Packaging Type | Bucket |
Grade Standard | Food Grade |
Product details:
Category | Water tanks, Swimming Pools and food processing industry |
Features | Non-Slip |
Packaging Size | 5 Ltr |
Grade Standard | Food Grade |
Minimum Order Quantity | 5 Litre |
Product description:
Bostik Epoxy Coat UW
- Two component epoxy paint
- Food grade paint
- water tanks
- swimming pools
- Food processing industry
Plug Leak
Minimum Order Quantity: 1 Kg
Product Brochure
Packaging Size | 5 kg |
Category | Crystalline Waterproofing, Acrylic Based Polymer Coating, Cementitious Waterproofing, Waterproofing Coating |
Location Type | Residential |
Types | Cementitious Waterproofing |
Form of Chemicals | Powder |
Application | Construction |
Shelf Life | 12 months |
Packaging Type | Bag |
Condition | New |
* It is a ready to use highly consistant,quick setting compound.
* Quick stoppage of water leakage.
* Less thermal cracking as it has low exothermic reaction.
Area of Application
+ Basement & pits
+ RCC water tanks
+ Concrete pipes
+ Sewage system
+ Water retaining structures
Packing : 5 Kg
Bostik Boscocrete /476
Product Brochure
Usage/Application | Bonding Agent |
Packaging Size | 1,5,20 kg |
Category | Acrylic Based Polymer Coating, Waterproofing Coating, Cementitious Waterproofing |
Color | White |
Brand | Bostik, Fosroc |
Application | All |
Type | Latex Based |
Packaging Type | Bottle |
Features | Bonding Agent |
Shelf Life | 12 months |
Surface of Application | Concrete |
Form of Chemicals | Liquid |
Purity | 45% |
Product Name | Bosco Crete |
Colour Of Mix | Milky White |
Product description:
BOSTIK BOSCOCRETE is a Acryllic Latex based waterproofing additive cum bonding agent.
RECOMMENDED USES
• Waterproofing of water tanks, roofs, balconies, terraces,wet areas, reservoir, swimming pools and fountains.
• Bonding old to new concrete.
• Additive for repair mortar.
PERFORMANCE PROPERTIES
Hydroment 476 HS 40% Boscocrete 30%
Pack: 20 Litre
Bostik Hydroment 476 Crete Hs / Boscocrete
Minimum Order Quantity: 5 Litre
Product Brochure
Type | Latex Based |
Form | Liquid |
Brand | Bostik India Pvt Ltd |
Packaging Size | 5,20,50,100 kg |
Coverage | 1sq.m/kg mix/in 2 coats |
Shelf Life | 12 months |
Surface Of Application | Waterproof Bonding Agent |
Color | Milky White |
Purity | 39 to 41% |
Specific Gravity | 1.01-1.04 |
Storage Condition | Cool and dry place away from sunlight, moisture and high humidity and have a shelf life of 12 months |
Mixing Ratio | Cement and Polymer 21 |
Features | Good Waterproofing Properties No Degradation On Long Term Exposure Excellent Bonding Properties |
Grade Standard | Industrial Grade |
Features:
- Good waterproofing property.
- No degradation on long-term exposure.
- Excellent bonding properties.
- Enhances strength durability of Repair Mortar.
- Suitable for external and internal repairs.
Procedure:
- The surface must be thoroughly cleaned to remove all dust debris.
- The surface should be free from oil, wax, or any other contaminations.
- Ensure the substrate is sound before application.
- Wet the surface before coating to achieve SSD condition.
- Mix cement and polymer in the ratio of 2:1 pbw to get uniform and consistent slurry by using low-speed stirrer.
- Apply material by stiff brush.
- Mix frequently to avoid setting during application.
- Minimum two coats to be applied in the interval of 5-6 hours.
- Wet the surface before application.
Bostik Flash Band
Product Brochure
Type | Pasting |
Packaging Size | Roll |
Usage/Application | Waterproofing, Roofs |
Brand | Bostik |
Water Proofing Material | Yes |
Coating Type | Pasting |
Bostik Flashband Self Adhesive Flashing Tape for Roofs is a flexible bitumen strip that bonds instantly to most building materials to provide a permanent, watertight seal.
Flashband is easily applied using just hand pressure and a seam roller and is ideal for new build, maintenance and repair projects, including:
ROOFING
- Replace damaged lead flashing
- Seal upstands and eve pieces
- Roof capping
- Edge flashing on roofing felt
- Repair roofing felt or joints on flat roofs
DRAINAGE
- Seal or repair valley gutters, guttering and down pipes
Flashband has four layers of protection, meaning it’s both tear and impact resistant and can withstand extreme temperatures of up to 100oC.
FOUR LAYERS OF PROTECTION
- Lacquer coating
- Heavy duty aluminium foil
- Tear resistant polyester membrane
- Polymer enhanced bitumen adhesive
Bostik Crack Fill
Minimum Order Quantity: 1 Kilogram
Product Brochure
State Of Matter | Powder, Paste |
Packaging Size | 1 kg |
Brand | Fosroc, Bostik, Asian |
Application | Walls |
Type Of Crack | Plaster |
Color | White |
Surface of Application | Roof, Wall |
Feature and Benefits:
Single component.
Non - shrinking.
Better adhesion.
Smooth finish.
Application Procedure:
Develop the crack in a "V" shaped groove.
Clean the groove by sprinkle of water to remove all the loose particles and dust.
Mix proportion Crack filler : Water - 3 :1 PBV.
Mix Crack Filler in water in a clean container.
Mix for 2-3 minutes to get smooth homogeneous paste.
Apply this paste into the groove with suitable trowel.
Finish the surface as required.
Coverage:
35 running meter / kg for 6 mm x 6 mm "V" shaped groove
Packaging:
1 & 5 Kg
Storage & Shelf Life:
12 months in original packing.
Additional Information:
- Pay Mode Terms: T/T (Bank Transfer),cash
Bostik LW Waterproofing Admixture
Minimum Order Quantity: 12 Litre
Types | Cementitious Waterproofing |
Packaging Size | 1 ltr, 5 ltr, 20 ltr |
Packaging Type | Can |
Brand | Bostik, Dr.Fixit, Fosroc, Cico, Sika, Basf |
Form | Liquid |
Shelf Life | 12 months |
Dosage (g) | 200ml/bag |
Color | Brown |
Condition | New |
Bostik lw is a chloride free admixture and supplied as brown liquid.
Areas Of Application:
- concrete roof slab.
- floor screeds in bathroom and damp areas.
- basement slabs and walls.
- concreting / internal plastering compliance - is2645-2003.
Dosage:
- 200 ml per 50 kg. Cement.
Packaging:
- 200ml,1,5,10,20,100 & 200 litre.
Storage & Shelf Life:
- 12 months.